Dreambox 800 HD SE Satellite Receiver Firmware

Dreambox 800 HD SE

Code Book

Feature

400 MHz MIPS processor
Enigma 2, Linux Operating System
Color OLED – Display
MPEG-2 / H.264 Hardware decoding
Tuner: DVB- S, optional: DVB- C, DVB- T
Tuner Module, Plug and Play
2 x Smart Card Reader (Dreamcrypt CA)
Mini USB for Service and software update
10 / 100Mbit Ethernet Interface
1 x Scart (RGB, FBAS or S-Video)
HDMI,
2 x USB 2.0 (eg keyboard)
Analog modem
Interface for digital bit S / PDIF stream out (AC-3)
64 Mbyte flash, 256 MB RAM
SATA
– The internal HDD, 2.5 “
TV / radio unlimited channel lists for
Channel change time <January 2
Automatic scanning service
Immediately bouquet list
EPG (Electronic Program Guide)
Many LNB- Switching control (DiSEqC supports)
OSD in many languages ​​and skin support
Videotext Decoder
External 12V power supply
DreamBox DM800 HD se technical data


DBS-Tuner DVB-S2 mit:
950 …. 2150 MHz frequency range
Demodulation DVB- S (QPSK); DVB-S2 (8PSK, QPSK)
DVB- S symbol rate: 2 … 45 Mbit / s, SCPC / MCPC
DVB-S2: 10-31 Mbit / s (8PSK), 10 -30 Mbit / s (QPSK)


Video decoder:
MPEG-2 and MPEG-1 compatible, H.264 video compression
Video Formats 4: 16.3: 9
4 letterbox: 3 TV devices


Audio decoder:
MPEG-1 and MPEG-2 Layer I and II Audiokompression, MP3
Dual sound mode (master / slave), stereo
Frequency: 32 kHz, 44.1 khz, 48 khz, 16 kHz, 22.05 kHz, 24 kHz


Analog output:
600 ohm output level L / R 0.5 VSS
THD> 60 dB (1 kHz)
Crosstalk <-65 dB


Digital output:
75 ohm output level of 0.5 VSS
Selective Filtering data 32 kHz, 44.1 khz, 48 khz
S / PDIF optical out, toslink


Ausgang Video:
75 ohm +/- 0.3 dB Ausgangspegel FBAS a VSS


Video options:
In the VSS 0.3 dB +/- 75 ohms Input Level FBAS
ETS 300 472 standard filter the teletext


TV-Scart:
Output: FBAS, RGB, S-Video


USB mini jack Service:
Function: Firmware Update


Ethernet:
10/100 Mbit compatible interface
Function: Firmware Update


Analoge modem:
Analoge modem for Internet connection


Interface:
Internal 2,5 “HDD


USB
2 x USB 2.0


LNB power and polarization in Tuner:
LNB Current 500mA max. Protected against short circuit protection
Supply at 400mA LNB Voltage vertical <without load 14V,> 11,5V
Supply 400mA LNB Voltage horizontal <without load 20V,> 17,3V


Count of active satellite position:
DiSEqC 1.0 / 1.1 / 1.2 and USALS (Rotor Control)


Power consumption:
12 V <15W


AC adapter
Log in:
110-240 AC / 50-60 Hz / 0,6A
Output:
12 = / 3,0A


Physical characteristics:
Ambient temperature of 15 ° C … + 35 ° C
Humidity <80%
Dimensions (W x D x H): 225 mm x 145 mm x 52 mm
Weight: HDD without 940 g

Power off Your box and open Loader

Select port com and select Networ or no Networ
If select Network then put IP of your PC and Box ip from yor Remot

First Press Connect Button from loader and power on your box
When Loader Connect with stb Press Flash button

Select Firmware You want to Upgrade and press open

Now Flash Upgrading will be Start and wait..

Ofter Flash Done Press ok and Disconnect the box from Loader and Exit.Restart Box and Enjoy with new Flash

Requirments
Image File Youwant To Upgrade in *nif Extension
DHCP Server, configured boot loader, Serial Cable, terminal program
like Hyper Term.
Browser Network Cable< Cros Cable if you want to Coneect Box Directly With PC.
For More Protection Use Second Stage Loader its Not Broken and Present
If You Don,t Have a DHCP Server Then Put IP in Loader Serial Port Setup
Shut Down The Dream Box From Power Switch or Deep Stand By Mode

1-Press and Hold the Front Panel Lower Button
2-Still Hold the Button and power on your Box
3-“*** STOP ***” These Text appear,if other text appear like “/flash”.. this Then you press and hold wrong lower Button.Now Leave the Lower button you hold.The boot loader will gon in Waiting Mode.
4-Above the “*** STOP ***” text, there must be an IP address (four decimal values with a dot in between) appear. If there appears the string “dhcp” instead, the box still looking for a DHCP server. A little wait. If it does not change, does not do anything with the DHCP server. Make sure the network cable is connected, etc.
if it is not workin then set ip Usin Serial Terminal

Open Browser in your PC
1-In Address line enter “http://ip/” where ip must be replaced with the value in the LCD
2-Press Firmware Upgrade Button in the Bottom of page

Now Select Image file you want to Upgrad Only in .nfi Extension Not in img etc
Click the flash button and wait it maybe
Restart your box and new Image willbe apear

take

If You don,t have a DHCP Server, configured or Ruter No Problem and don,t Instal one.Only you need to connect a serial terminal now
That’s why you need the IP address of your Dreambox gives. Your IP I, asksomeone help please, do not know what to choose. Your computer, your “next” IP address, you can choose any IP address but can not be used by another device theIP is. Another device is used as an example, your computer’s IP address is 192.168.0.5, and you, use192.168.0.10 said. In this case, only 192.168.0.11. Or whatever. This is the only x> = 1 and <= range 192.168.0.x, I, where 254,.
Hyperterm For example, start your favorite terminal program. Com port 115200 / 8N1 set. “S” Press.
Now you should see the setup menu. It should look like the following screenshot

Press the right arrow. You are now in the network setup menu.
Using “+” or “-” you can use the “Network Type” to see the series “Manual”.
Now you can enter an IP address below. Press F9 to save your settings.
Dreambox close.

Now go back and the procedure again. “DHCP” may not be displayed, instead of the IP you entered